- 您现在的位置：买卖IC网 > Sheet目录951 > 9578674002 (TE Connectivity)HEAT SHRINK TUBING
Page 4
4.3.5
4.3.6
4.4
5.
5.1
5.2
5.3
SPECIFICATION RW-3009 ISSUE 3
Dielectric Withstand, Breakdown, and Strength
The dielectric strength of the tubing shall be measured under oil in accordance with ASTM D 2671. Five
150-mm (6-inch) specimens of tubing shall be recovered over a metal mandrel by conditioning for 3 minutes
in a 200 ± 3°C (392 ± 5°F) oven. The mandrel diameter shall be slightly larger than the fully recovered
inside diameter of the tubing being tested. The metal mandrel shall serve as one electrode and a 25mm (1-
inch) wide strip of lead foil wrapped around the outside of the tubing as the other electrode. The test voltage
shall be applied at a rate of rise of 500 volts per second. Thickness measurements for calculating dielectric
strength shall be made adjacent to the point of breakdown. Specimens for dielectric withstand shall be held
for 60 seconds at 2500 volts.
Corrosive Effect
Three specimens of tubing shall be tested for copper contact corrosion in accordance with ASTM D 2671,
Procedure B. Three specimens shall be conditioned for 7 days in a 158.0 ± 1.0°C (316.4 ± 1.8°F) oven.
After conditioning, the specimens shall be visually examined for evidence of corrosion.
REJECTION AND RETEST
Failure of any samples of tubing to conform to any one of the requirements of this specification shall be
cause for rejection of the lot represented. Tubing which has been rejected may be replaced or reworked to
correct the defect and then resubmitted for acceptance. Before resubmitting, full particulars concerning the
rejection and the action taken to correct the defect shall be furnished to the inspector.
PREPARATION FOR DELIVERY
FORM
The tubing shall be supplied on spools, unless otherwise specified.
PACKAGING
Packaging shall be in accordance with good commercial practice.
MARKING
Each container of tubing shall be permanently and legibly marked with the size, quantity, manufacturer's
identification, specification number, product designation, and lot number.
If this document is printed it becomes uncontrolled. Check for the latest revision.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
964073-000
CABLE TERMINATION RG/U 178,404
9665.1300
TRANSIPILLAR HEX M6 THR 51MM
9668274002
HEAT SHRINK TUBING
971078-000
MOLDED TRANSITION Y SHAPE
974559-000
S02-08-R-3
9864-PSM0
CONN HOUSING CARRIER 64POS SHORT
991265-001
HEAT SHRINKABLE CABLE ENTRY SEAL
992899-000
D-110-0181
相关代理商/技术参数
9578A-SS-1032-7
制造商:Amatom Electronic Hardware 功能描述:
9578D-A-0632-10A
制造商:Amatom Electronic Hardware 功能描述:
9578D-A-0832-17
制造商:Amatom Electronic Hardware 功能描述:
9578D-SS-1032-7
制造商:Amatom Electronic Hardware 功能描述:
9579
功能描述:螺丝和紧固件 1/2 No.8 Hex Head SELF TAP SCREW
RoHS:否 制造商:Unspecified 产品: 类型:Washer 螺纹大小: 长度: 材料:Steel 电镀:Nickel 螺丝头: 螺丝类型:
9579 1 1/2 X 36 YD (BULK)
制造商:3M Electronic Products Division 功能描述:70006151941 9579 1 1/2 X 36 YD BULK
9579 0021000
制造商:Belden Inc 功能描述:SHLD MULTICOND CABLE, 4COND, 16AWG, 1000FT, 300V; Reel Length (Imperial):1000ft; Reel Length (Metric):304.8m; No. of Conductors:4; Conductor Size AWG:16AWG; Voltage Rating:300V; No. of Strands x Strand Size:1 x 16AWG ;RoHS Compliant: Yes
9579 002BULK
制造商:Belden Inc 功能描述:4 #16 PVC SHLD PVC RED BULK